HOW TO HALF TIME IN GROSS BEAT HOW TO
HOW TO HALF TIME IN GROSS BEAT FULL
HOW TO HALF TIME IN GROSS BEAT SERIES

The playback position, direction and speed. The Time envelope is a sample 'offset' envelope, i.e.

Time Mapping Envelopes - These envelopes control playback of the audio from the 2-bar, rolling, audio buffer.

NOTE: You can change the slope in semitone units using the Mapping Options menu (select the right-most point defining a slope and apply the 1 semitone up / down function). Reverse, depending on the angle of the line. Slopes steeper than this line will play fast reverse, shallower will be slow

Reverse guides - The multiple grey diagonal lines show the slope required to effect a normal speed reverse playback.

Bear in mind that if you move into a new section of the song, change from verse to chorus for example, the previous two bars will be stored in the buffer and may not match the audio needed for the new section until After two bars have played thenДЄny mapping curve is safe.

HOW TO HALF TIME IN GROSS BEAT FULL

If you need to start a song with a full audioД«uffer add two pre-song bars (with audio, of course) and start with a Volume mapping envelope flat-lining line along the bottom of the Mapping Area, so the pre-bars won't be heard. While it's not shown, imagine the Safety Line continues down to the end of the second bar.

If the Time mapping envelope goes below the Safety Line before the time-marker reaches that point, silence will be heard (or is that Gross Beat implodes creating an EMP, causing satellites toДЇall out of the sky? I can't remember, you will just have to experiment). The position of the Playback Locator) has buffered audio while the area below does not. The area above the Safety Line (and behind The Safety Line shows the safe area for mapping envelopes during the first bar of a song.

Safety line - The single dark 'Safety Line' cuts across the first 4 beats.

Angled guide markings - You will notice single darker and multiple lighter angled lines across the mapping area:.

The beat is indicated by the Playback locator - a vertical green scrolling line, visible only when the host is playing.

the plugin has received at least 2 bars of audio). This means it is possible to step back up to 8 beats (2 bars) from the current playback position, as long as

Width vs height - The mapping panel is 4 beats (1 bar) wide and 8 beats (2 bars) high.

Open a context menu with options for graphing shapes (as shown in the screen shot, right). Top-left is a drop-down menu (as described below).

HOW TO HALF TIME IN GROSS BEAT SERIES

Mapping controls - A series of controls & options run down the left side and under the mapping area.ItвЂ™s a technique that I use constantly and IвЂ™m sure that once you master it, youвЂ™ll be using it quite often too.Дo you use half time and double time transitions in your DJ sets? Have any special tricks or tips to share about them? Do so in the comments below.The envelope mapping panel displays the selected Time or Volume mapping envelope (slots are directly left of the Mapping Panel). Being able to completely flip the energy of your set for your audience quickly is invaluable.

HOW TO HALF TIME IN GROSS BEAT HOW TO

Learning how to utilise half and double time adds a great tool to your arsenal as a DJ.

Begin beatmix keeping the number of double/half time bars to have proper phrasing (eg four bars of 60BPM song = eight bars of 120 BPM song).

Select a song thatвЂ™s either half or double the tempo of the song in deck A.

Half time / double time transitions provide a вЂњwowвЂќ factor in your DJ set and can surprise the audience with a sudden yet smooth change in energy and musical direction. If you are using a double time transition, two bars of the вЂњdouble time songвЂќ is equal to one bar of the song you are mixing into.Д®xample: two bars at 120BPM = one bar at 60BPM If you are using a half time transition, one bar of the вЂњhalf time songвЂќ is equal to two bars of the song you are mixing into.Д®xample: one bar at 60BPM = two bars at 120BPM One thing that you may have to keep in mind is how to calculate the bars when using half / double time transitions. The same can be done vice versa, if you are playing a song that is 70BPM beatmixing a 140BPM song should work quite well. For example if you are playing a song that is 120BPM you can beatmix a song that is 60BPM and they should mix smoothly in most cases. Half time and double time refers to using a song that is either half or double the tempo of the song that is currently playing. One of my favourite tempo related tricks is using half time / double time to make smooth, big tempo changes. Understanding how the math behind these works improves your mixing. DJing is a technical artform: Song structure, counting beats and bars, and tempo are essential aspects of DJing.

How to half time in gross beat